How to get to the drain pump

cookiemagnate
5 Min Read
How to get to the drain pump
2 Comments
Subscribe
Notify of
2 Comments
Oldest
Newest Most Voted
Inline Feedbacks
View all comments

Look up your brand and model # on YouTube and drain pump replacement. It will have step by step of what to disassemble and how. It will also give you tools you’ll need, as well as tips on supporting parts as you break it down. Most machines I have repaired i did it this way. Also, Most I have worked on open the top panel first, then the front panel.

The one I worked on I had to get at the pump from the bottom of unit. Disconnecting 2 hoses, 1 electrical plug and couple screws to pull pump. Easier than I expected.

How to Get to the Drain Pump: A Step-by-Step Guide

The drain pump is an essential component in your home’s plumbing system, responsible for removing waste water from your sink, shower, and washing machine. However, if you’re experiencing issues with clogs, leaks, or poor drainage, you may need to access the drain pump to diagnose and fix the problem. In this article, we’ll walk you through the steps on how to get to the drain pump, ensuring you’re prepared for the task.

Before You Begin

Before attempting to access the drain pump, take the following precautions:

  1. Turn off the power: Locate the power shut-off valve and switch it off to prevent electrical shock.
  2. Disconnect the water supply: Find the shut-off valve for the water supply lines and turn it off to prevent water from flowing into the drain pump.
  3. Wear protective gear: Wear rubber gloves, safety glasses, and a dust mask to protect yourself from potential water spills and debris.

Identifying the Drain Pump Location

The drain pump can be located in different areas depending on your home’s plumbing system. Common locations include:

  1. Under the sink: Some sink drains have a pop-up drain assembly with a removable cover plate that hides the drain pump.
  2. Behind the wall: In some cases, the drain pump is situated behind a wall, accessed through a removable panel or a trap door.
  3. In the crawl space or basement: Older homes or those with septic systems may have the drain pump located in the crawl space or basement.

Accessing the Drain Pump

Once you’ve identified the location of your drain pump, follow these steps to access it:

  1. Remove the cover plate or panel: If your drain pump is located under the sink or behind a wall, simply remove the cover plate or panel to expose the drain pump.
  2. Disconnect the drain line: Carefully disconnect the drain line from the drain pump to prevent any debris from entering the pump.
  3. Remove any excess water: Use a towel or sponge to remove any excess water from the area to prevent slipping or accidental electrical shock.
  4. Access the drain pump: You should now be able to access the drain pump. Take note of any wiring, electrical components, or other features surrounding the pump.

Important Safety Reminders

Remember to exercise caution when accessing the drain pump:

  1. Avoid electrical shocks: Keep away from exposed wiring and electrical components.
  2. Watch out for sharp edges: Be mindful of sharp edges or corners around the drain pump.
  3. Take your time: Move slowly and carefully to avoid damaging surrounding components or structures.

Conclusion

Accessing the drain pump may require some patience and effort, but with the right steps and precautions, you can successfully diagnose and fix common issues. Remember to prioritize safety and take your time when working with electrical components and water systems.

This is a Kenmore Elite topload washer. Recently, the washer quit draining during its cycle.

I'm trying to get behind it to the drain pump. I'm hoping it's just got something stuck in there or hopefully drain pumps are inexpensive… but I have no clue how to easily get in the back. It's got all these plastic stud-like pieces and some screws, as well as plastic sliders on the side.

I'm trying to get this open efficiently. I really don't want to just go about removing things willy nilly. Also the only way I can see to remove the sliders is by tipping the washer on its face, and – despite my best efforts – there's still some water at the bottom. I really don't want to deal with spillage.

All in all, this was not what I was expecting when I took a look behind the washer. It looks like a needlessly complicated jigsaw puzzle, and I don't know where to go from here. Any advice is much appreciated!

TAGGED:
Share This Article
2
0
Would love your thoughts, please comment.x
()
x